<p dir="ltr">It is hard to say exactly without repeating the calculation why it is a little slow. If it takes 80 cycles for a point calculation with MSR1, 300 in MSR1a is not a lot.</p>
<p dir="ltr">Often TEMPS converges better than TETRA as it broadens the electronic phase changes to second order so the problem is more analytic. I normally use 0.0018 room temperature).</p>
<p dir="ltr">___________________________<br>
Professor Laurence Marks<br>
Department of Materials Science and Engineering<br>
Northwestern University<br>
<a href="http://www.numis.northwestern.edu">www.numis.northwestern.edu</a><br>
<a href="http://MURI4D.numis.northwestern.edu">MURI4D.numis.northwestern.edu</a><br>
Co-Editor, Acta Cryst A<br>
"Research is to see what everybody else has seen, and to think what nobody else has thought"<br>
Albert Szent-Gyorgi</p>
<div class="gmail_quot<blockquote class=" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>
<div dir="ltr">
<div>
<div>Thanks for your response. Even if I do a simple scf calculation with MSR1, the charge does not converge with -cc 0.001 for about 200 iterations. Anyway I lower the -cc tolerance and give it a try.<br>
</div>
Meanwhile any other idea/suggestion/comment or problem that has been spotted......
<br>
</div>
Some of my input files are attached, if they could help.<br>
</div>
<div class="gmail_extra"><br>
<div class="gmail_quote">On 16 December 2014 at 12:35, Lyudmila Dobysheva <span dir="ltr">
<<a href="mailto:lyuka17@mail.ru" target="_blank">lyuka17@mail.ru</a>></span> wrote:
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<span>On 16.12.2014 08:56, Shafqat Hussain Shah wrote:<br>
</span>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<span>the atomic positions of the system using MSR1a, it is, unexpectedly,<br>
very slow (around 300 iterations) in charge convergence.<br>
</span><span>runsp_lapw -p -i 999 -ec 0.0001 -cc 0.001 -fc 0.50<br>
</span><span>all<br>
the calculations with experimental parameters and Optimizer generated<br>
structures for option 1, 3 and 4 converge nicely (around 80 iterations<br>
with the above mentioned command).<br>
</span></blockquote>
<br>
As far as I remember a standard procedure for MSR1a should start from a partly converged solution, that is, first, without MSR1a:<br>
run_lapw -p -cc 0.1 -ec 0.25 -fc 20 -i 60<br>
save (to clean the directory)<br>
then change the case.inm to MSR1a<br>
and run_lapw with good criteria for convergence -cc 0.0015<br>
<br>
I see that in the first iteration you have<br>
:DIS= ( 1.5480230 for atom 3 spin 2) 2.9889210<br>
that is rather large. The calculated forces are not correct yet, your system goes far from reality. Maybe for experimental lattice you had started from a converged solution, so forces had been correct in the first iteration already, and finding the equilibrium
was short.<br>
<br>
Best regards<br>
Lyudmila Dobysheva<br>
------------------------------<u></u>------------------------------<u></u>------<br>
Phys.-Techn. Institute of Ural Br. of Russian Ac. of Sci.<br>
426001 Izhevsk, ul.Kirova 132<br>
RUSSIA<br>
------------------------------<u></u>------------------------------<u></u>------<br>
Tel.:7(3412) 218988(office), 722529(Fax)<br>
E-mail: <a href="mailto:lyu@ftiudm.ru" target="_blank">lyu@ftiudm.ru</a>, <a href="mailto:lyuka17@mail.ru" target="_blank">
lyuka17@mail.ru</a> (office)<br>
<a href="mailto:lyuka17@gmail.com" target="_blank">lyuka17@gmail.com</a> (home)<br>
Skype: lyuka17 (home), lyuka18 (office)<br>
<a href="http://fti.udm.ru/content/view/25/103/lang,english/" target="_blank">http://fti.udm.ru/content/<u></u>view/25/103/lang,english/</a><br>
------------------------------<u></u>------------------------------<u></u>------<br>
______________________________<u></u>_________________<br>
Wien mailing list<br>
<a href="mailto:Wien@zeus.theochem.tuwien.ac.at" target="_blank">Wien@zeus.theochem.tuwien.ac.<u></u>at</a><br>
<a href="http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien" target="_blank">http://zeus.theochem.tuwien.<u></u>ac.at/mailman/listinfo/wien</a><br>
SEARCH the MAILING-LIST at: <a href="http://www.mail-archive.com/wien@zeus.theochem.tuwien.ac.at/index.html" target="_blank">
http://www.mail-archive.com/<u></u>wien@zeus.theochem.tuwien.ac.<u></u>at/index.html</a><br>
</blockquote>
</div>
<br clear="all">
<br>
-- <br>
<div>Dr. Shafqat Hussain Shah<br>
</div>
</div>
</div>
</div>