<div dir="auto">I did not write notes on cell optimizations, just MSR1a. Swamped.<br><br><div data-smartmail="gmail_signature">---<br>Professor Laurence Marks<br>"Research is to see what everybody else has seen, and to think what nobody else has thought", Albert Szent-Gyorgi<br><a href="http://www.numis.northwestern.edu">http://www.numis.northwestern.edu</a><br>Corrosion in 4D <a href="http://MURI4D.numis.northwestern.edu">http://MURI4D.numis.northwestern.edu</a><br>Partner of the CFW 100% gender equity project, <a href="http://www.cfw.org/100-percent">www.cfw.org/100-percent</a><br>Co-Editor, Acta Cryst A<br>    </div></div><div class="gmail_extra"><br><div class="gmail_quote">On Oct 12, 2017 17:05, "Dr. K. C. Bhamu" <<a href="mailto:kcbhamu85@gmail.com">kcbhamu85@gmail.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">



<div>
<div dir="ltr">
<div>
<div>
<div>
<div>
<div>
<div>
<div>
<div>Dear Prof. Marks,<br>
<br>
</div>
I read your optimization notes for orthorhombic cell and tried to optimize an orthorhombic cell but I could not obtain an optimization plot.
<br>
</div>
<br>
<br>
</div>
So I am following the standard procedure as below taken from your suggestion in the mailing list
<a href="https://urldefense.proofpoint.com/v2/url?u=https-3A__www.mail-2Darchive.com_wien-40zeus.theochem.tuwien.ac.at_msg06932.html&d=DwMFaQ&c=yHlS04HhBraes5BQ9ueu5zKhE7rtNXt_d012z2PA6ws&r=U_T4PL6jwANfAy4rnxTj8IUxm818jnvqKFdqWLwmqg0&m=CCwrrgUZT3FHbBbTKhyWl219yV58Vhv95TA_U_uQYds&s=3Z2BD0hubIJEMETcqg_8zHYeAIXe5P9S2fezgiH9Zgg&e=" target="_blank">
https://www.mail-archive.com/w<wbr>ien@zeus.theochem.tuwien.ac.at<wbr>/msg06932.html</a>)  and have a queries:</div>
<div><br>
</div>
<div>The procedure is a four-step task what I am following:</div>
<div><br>
</div>
<div>The original lattice parameters were: a, b, c=16.763005, 24.803600, 16.320431  >> vol 6785.64777697697 bohr^3.</div>
<div><br>
</div>
<div><br>
</div>
1.   VARY C/A RATIO with CONSTANT VOLUME and B/A (orthorh lattice)<br>
<br>
</div>
getting below optimized data: <br>
 =============================<wbr>=============================<br>
Lowest point on X-axis is =  -1.615800<br>
Minimum value of B/A is =     1.455755<br>
Minimum value of ENE is =   -339059.104498 Ry<br>
 =============================<wbr>=============================<br>
Value of A is =     16.85428 bohr  ;    8.91890 Ang<br>
Value of B is =     24.53569 bohr  ;   12.98373 Ang<br>
Value of C is =     16.40929 bohr  ;    8.68342 Ang<br>
 =============================<wbr>=============================<br>
Initial value of  B/A is =          1.479663<br>
Conv. Unit Cell Vol =  6785.7557 bohr^3 ; **********Ang^<br>
  <br>
</div>
<br>
</div>
2.  Volume optimization using option 1 in "x optimize" and then calculating new volume from eplot option.</div>
<div><br>
</div>
<div><br>
</div>
<div>Query: Step two is giving optimized volume but I do not know how to calculate lattices parameters from a single volume
<br>
</div>
<div>value for the next step "VARY C/A RATIO with CONSTANT VOLUME and B/A (orthorh lattice)"?</div>
<div><br>
</div>
<div><br>
</div>
<div>The original cell volume and lattice parameters are mentioned at the beginning.</div>
<div><br>
</div>
<div>and the new volume from step two is: 6815.3427 bohr^3</div>
<div><br>
</div>
<div><br>
</div>
<div><br>
</div>
<div>The above same query is for the remaining process:</div>
<div><br>
</div>
<div>3. optimization of C/A <br>
</div>
<div><br>
</div>
<div>4. optimization of V.</div>
<div><br>
</div>
<div><br>
</div>
<div>*5 At the final step I will do structural relaxation (min_.....).<br>
</div>
<div><br>
</div>
<div><br>
</div>
<div>Could you please advice me how to proceed?</div>
<div><br>
</div>
<div><br>
</div>
<div><br>
</div>
<div>Kind regards,</div>
<div>Bhamu<br>
</div>
<div>
<div><br>
<br>
<div><br>
<div><br>
</div>
</div>
</div>
</div>
</div>
</div>

</blockquote></div></div>