<div dir="ltr">Dear Sir,<div><br></div><div>           Initially the structure was optimized with nlvdw and spin polarization to check Ca intercalation voltage in it. Promising results were found. However, during elastic properties calculation I have taken the optimize structure a priori and run the command run_lapw. I guess, even if the initial structure was for spin polarized for non spin polarize calculation it should get the optimized structure while using the command run_lapw -ec 0.0001 -cc 0.0001 -fc 1.0 -min...what is your advice in this regard?</div><div> </div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, 10 Aug 2024 at 18:43, Laurence Marks <<a href="mailto:laurence.marks@gmail.com">laurence.marks@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto"><div><div>Please read your email carefully, and use the computer behind your eyes.</div><div dir="auto"><br></div><div>"optimized by using spin polarization and nlvdw"<br></div><div dir="auto">"running command; run_lapw ..."</div><div dir="auto"><br></div><div dir="auto">Are these the same?</div><div>___<br>Professor Laurence Marks (Laurie)<br>Department of Materials Science and Engineering, Northwestern University<br><a href="http://www.numis.northwestern.edu" target="_blank">www.numis.northwestern.edu</a><br>"Research is to see what everybody else has seen, and to think what nobody else has thought" Albert Szent-Györgyi</div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, Aug 10, 2024, 07:50 shamik chakrabarti <<a href="mailto:shamik15041981@gmail.com" target="_blank">shamik15041981@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">Dear Sir,<div><br></div><div>           I have used the optimized structure of SnSe2, which is optimized by using spin polarization and nlvdw. Now, this optimized file is used as an input for set_elast_lapw. I have used the running command; <b>run_lapw -ec 0.0001 -cc 0.0001 -fc 1.0 -min</b></div><div><b><br></b></div><div>I have obtained the following values of elastic constants; c11=90.8145, c12=23.8215, c13=18.9015, c33=21.961 & c55=4.368 (I have considered fit 2)</div><div><br></div><div>However, the elastic constants reported in the literatures are;c11=111, c12=33.39, c13=33.08, c33 = 22.63, c44=44.48, c66= 38.80</div><div><br></div><div>Please advice.</div><div><br></div><div>with regards,</div><div><br></div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, 10 Aug 2024 at 17:14, morteza jamal <<a href="mailto:m_jamal57@yahoo.com" rel="noreferrer" target="_blank">m_jamal57@yahoo.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">When the sensitivity of elastic constant calculations ignores with respect to the order of fit.<div><br></div><div>However from view point of theory, when the strain is small ( very small) , the optimized value for order of fit is 2. </div><div><br></div><div>IRelast package checks sensitivity of elastic constants calculations  to the order of fit and prints them.</div></blockquote></div><br clear="all"><div><br></div><span class="gmail_signature_prefix">-- </span><br><div dir="ltr" class="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div style="font-size:small">Dr. Shamik Chakrabarti</div><div style="font-size:small">Research Fellow </div><div style="font-size:small">Department of Physics</div><div style="font-size:small">Indian Institute of Technology Patna</div><div style="font-size:small">Bihta-801103</div><div style="font-size:small">Patna</div><div style="font-size:small">Bihar, India</div></div></div></div></div></div></div></div>
_______________________________________________<br>
Wien mailing list<br>
<a href="mailto:Wien@zeus.theochem.tuwien.ac.at" rel="noreferrer" target="_blank">Wien@zeus.theochem.tuwien.ac.at</a><br>
<a href="http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien" rel="noreferrer noreferrer" target="_blank">http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien</a><br>
SEARCH the MAILING-LIST at:  <a href="http://www.mail-archive.com/wien@zeus.theochem.tuwien.ac.at/index.html" rel="noreferrer noreferrer" target="_blank">http://www.mail-archive.com/wien@zeus.theochem.tuwien.ac.at/index.html</a><br>
</blockquote></div></div></div>
_______________________________________________<br>
Wien mailing list<br>
<a href="mailto:Wien@zeus.theochem.tuwien.ac.at" target="_blank">Wien@zeus.theochem.tuwien.ac.at</a><br>
<a href="http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien" rel="noreferrer" target="_blank">http://zeus.theochem.tuwien.ac.at/mailman/listinfo/wien</a><br>
SEARCH the MAILING-LIST at:  <a href="http://www.mail-archive.com/wien@zeus.theochem.tuwien.ac.at/index.html" rel="noreferrer" target="_blank">http://www.mail-archive.com/wien@zeus.theochem.tuwien.ac.at/index.html</a><br>
</blockquote></div><br clear="all"><div><br></div><span class="gmail_signature_prefix">-- </span><br><div dir="ltr" class="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div style="font-size:small">Dr. Shamik Chakrabarti</div><div style="font-size:small">Research Fellow </div><div style="font-size:small">Department of Physics</div><div style="font-size:small">Indian Institute of Technology Patna</div><div style="font-size:small">Bihta-801103</div><div style="font-size:small">Patna</div><div style="font-size:small">Bihar, India</div></div></div></div></div></div></div></div>